STM32F103VCT6 (ARM Cortex M3) Development Board+128M NAND Flash. dekoder MP3 + USB host ...
/kliknij na zdjęcie aby powiększyć/
Specyfikacja modułu
● CPU: STM32F103VCT6 STMicroelectronics High-density performance line ARM-based 32-bit MCU with 256k Flash,48k RAM (on chip 12Bit A/D、D/A、PWM、CAN、USB、SDIO、FSMC……)。ARM Cortex-M3 running at up to 72 MHzThumb-2 instruction set72 MHz maximum frequency,1.25 DMIPS/MHz (Dhrystone 2.1)performance at 0 wait state memory accessSingle-cycle multiplication and hardware division
● support a 2.8" TFT Color LCD module or a 3.2" TFT Color LCD module (Default) , 240*RGB*320 pixels 262k color
support 8-bit/16-bit parallel bus interface IO control mode, TSC2046 touch panel controller onboard directly compatible with ADS7843 on TFT Color LCD module, Support a SD card interface (SPI mode)Support a ATMEL DataFlash AT45DBxxx series device
● 128M or 256M NAND FLASH on board, IO control mode, can replacing more by yourself, for example: 1Gb 2Gb 4Gb and so on. ● VS1003B MP3 decoder device on board.VS1003 is a single-chip MP3/WMA/MIDI audio decoder and ADPCM encoder. It contains a high-performance, proprietary low-power DSP processor core VS DSP4, working data memory, 5 KiB instruction RAM and 0.5 KiB data RAM for user applications, serial control and input data interfaces,4 general purpose I/O pins, an UART, as well as a high-quality variable-sample-rate mono ADC and stereo DAC, followed by an earphone amplifier and a common buffer.
● 128M or 256M NAND FLASH on board, IO control mode, can replacing more by yourself, for example: 1Gb 2Gb 4Gb and so on.
● VS1003B MP3 decoder device on board.VS1003 is a single-chip MP3/WMA/MIDI audio decoder and ADPCM encoder. It contains a high-performance, proprietary low-power DSP processor core VS DSP4, working data memory, 5 KiB instruction RAM and 0.5 KiB data RAM for user applications, serial control and input data interfaces,4 general purpose I/O pins, an UART, as well as a high-quality variable-sample-rate mono ADC and stereo DAC, followed by an earphone amplifier and a common buffer.
● a USB host interface, driver IC is CH376.CH376 is file manage and control IC. Application for MCU read USB disk or SD Card file system.CH376 support USB device andUSB host mode, integration USB communications protocol firmware, integration Mass-Storage device protocol firmware, integration FAT12 FAT16 FAT32 file manage system, support any USB Storage device (include U disk, USB hard disk, SD Card……)Support 1.5Mbps Low Speed and 12Mbps Full Speed USB, compatible USB 2.0Support USB-host interface and USB-device interface, support dynamic switch USB-host and USB-device modeSupport USB device Control Transfers, Interrupt Transfers, Bulk Transfers
● A MicroChip ENC28J60 10Mbit Ethernet controller IC , IEEE 802.3 compatible Ethernet controller,Integrated MAC and 10BASE-T PHY ,Supports one 10BASE-T port with automatic polarity detection and correction,Supports Full and Half-Duplex modes,on-board RJ45 connector with build in Ethernet transformer and two status LEDs easy interface to any microcontroller via SPI ● A USB device interface (STM32F103VCT6 inside)● a CAN communications interface, driver IC is SN65VHD230● a RS485 communications interface,driver IC is SP3485● two RS232 interface● a SD Card interface (SPI conterll mode)● a I2C interface (connect 24LC02 EEPROM)● a SPI interface (connect AT45DB161D data flash)● one way ADC adjust input ● two way ADC socket input ● one way DAC socket output ● one beep, four programmable user LED, one power show LED, one USB show LED, three programmable user key, a five direction jockey, one RESET key● support 5V Power Supply and USB Power Supply input ● All IO port all the leads, user-friendly expansion of functionality, secondary development ● Dimensions: 15cm x 11cm
● A MicroChip ENC28J60 10Mbit Ethernet controller IC , IEEE 802.3 compatible Ethernet controller,Integrated MAC and 10BASE-T PHY ,Supports one 10BASE-T port with automatic polarity detection and correction,Supports Full and Half-Duplex modes,on-board RJ45 connector with build in Ethernet transformer and two status LEDs easy interface to any microcontroller via SPI
● A USB device interface (STM32F103VCT6 inside)● a CAN communications interface, driver IC is SN65VHD230● a RS485 communications interface,driver IC is SP3485● two RS232 interface● a SD Card interface (SPI conterll mode)● a I2C interface (connect 24LC02 EEPROM)● a SPI interface (connect AT45DB161D data flash)● one way ADC adjust input ● two way ADC socket input ● one way DAC socket output
● one beep, four programmable user LED, one power show LED, one USB show LED, three programmable user key, a five direction jockey, one RESET key● support 5V Power Supply and USB Power Supply input
● All IO port all the leads, user-friendly expansion of functionality, secondary development
● Dimensions: 15cm x 11cm
schemat /kliknij aby powiększyć/ Kupując zestaw otrzymyjesz : Płyte bazową z kontrolerem STM32, z wgrany programem demo Kabel USB Kabel RS 232 Kabel sieciowy Ethernet Bateria potrzymująca CR1220 zasilacz 5V / 1000mA /umożliwia niezależne zasilanie układu, port USB pozostaje wolny/ CD-ROM zawiera schematy, noty katalogowe, oprogramowanie oraz przykładowe programy
schemat /kliknij aby powiększyć/
Kupując zestaw otrzymyjesz :
Płytkę można programować poprzez port RS232/w zestawie oprogramowanie na komputer PC, oraz przewód/, mikrokontroler posiada wgrany bootloader. Na innej aukcji jest dostępny moduł wraz z wyświetlaczem 3.2" lub 2.8" z ekranami dotykowymi. Na zakupiony towar otrzymaujesz paragon, lub rachunek. Wysyłka towaru w 24h, po zaksięgowaniu wpłaty. Masz pytanie, proszę pisać na e-mail lub GG
Płytkę można programować poprzez port RS232/w zestawie oprogramowanie na komputer PC, oraz przewód/, mikrokontroler posiada wgrany bootloader.
Na innej aukcji jest dostępny moduł wraz z wyświetlaczem 3.2" lub 2.8" z ekranami dotykowymi.
Na zakupiony towar otrzymaujesz paragon, lub rachunek.
Wysyłka towaru w 24h, po zaksięgowaniu wpłaty.
Masz pytanie, proszę pisać na e-mail lub GG
