Zestaw uruchomieniowy STM32 z mikrokontrolerem STM32F407VET6

ARM Cortex M4 32-bit RISC

192+4 KB SRAM / 512 KB Flash

1. STM32F407VET6: the high performance STM32 MCU which features:
• Core: Cortex-M4 32-bit RISC
• Feature: a full set of single-cycle DSP instructions
• Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
• Operating Voltage: 1.8V-3.6V
• Package: LQFP100
• Memories: 512kB Flash, 192+4kB SRAM
• MCU communication Interfaces:
• 3 x SPI, 3 x USART, 2 x UART, 2 x I2S, 3 x I2C
• 1 x FSMC, 1 x SDIO, 2 x CAN
• 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
• 1 x 10/100 Ethernet MAC
• 1 x 8 to 12-bit parallel camera interface
• AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
• Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
2. Onboard 3.3V regulator, AMS1117-3.3
3. Power indicator
4. User LEDs: These LEDs are connected to the MCU pin via jumpers, used for indicating IO status or program running status while debugging
5. Reset button
6. User Buttons
7. Joystick, 5 directions
8. 25M crystal oscillator
9. 32.768K crystal, used for internal RTC, also supports clock calibration.
10. Programming interface (JTAG/SWD), onboard 20-pin JTAG/SWD header
11. USB connector, used for establishing USB communication between PC and the STM32 development board
12. USART1 pin header, supports ISP (In-System Programming) through USART1, as well as system signal output
13. IO expander, all the MCU pins are accessible on expansion connectors for further expansion
14. Power input/output header, 5V/3.3V, usually used for power output, or common ground with other user board
15. 5V DC power jack
16. Boot modes configuration: jumpers for selecting STM32 boot space
17. Jumper for selecting power supply, powered from 5V DC jack or USB connection
18. OTG PWR OUT enable jumper
    • short the jumper to enable OTG PWR OUT
    • open the jumper to disable, as well as taking up no I/O port
19. OTG VBUS enable jumper
    • short the jumper to enable OTG VBUS
    • open the jumper to disable, as well as taking up no I/O port
20. VBAT enable jumper, powered from battery is available via this jumper, an external battery is required
21. VREF jumper
    • Short the jumper to connect VREF+/VREF- respectively to VCC/GND
    • Open the jumper to connect VREF+/VREF- to other custom pins via jumper wires
22. User LEDs jumper
    • Short the jumper to connect to I/Os that used in example code
    • Open the jumper to connect to other custom pins via jumper wires
23. User Buttons jumper
• Short the jumper to connect to I/Os that used in example code
• Open the jumper to connect to other custom pins via jumper wires
24. Joystick jumper
    • Short the jumper to connect to I/Os that used in example code
    • Open the jumper to connect to other custom pins via jumper wires