1. STM32F407ZGT6: the high performance STM32 MCU which features:
   • Core: Cortex-M4 32-bit RISC
   • Feature: a full set of single-cycle DSP instructions
   • Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
   • Operating Voltage: 1.8V-3.6V
   • Package: LQFP144
   • Memories: 1024kB Flash, 192+4kB SRAM
   • MCU communication Interfaces:
     • 3 x SPI, 3 x USART, 2 x UART, 2 x I2S, 3 x I2C
     • 1 x FSMC, 1 x SDIO, 2 x CAN
     • 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
     • 1 x 10/100 Ethernet MAC
     • 1 x 8 to 12-bit parallel camera interface
   • AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
   • Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
2. AMS1117-3.3: 3.3V voltage regulator
3. Power indicator
4. LEDs: convenient for indicating I/O status or program debugging running state
5. Reset button
6. User keys
7. Joystick: five positions
8. 25M crystal oscillator
9. 32.768K crystal, used for internal RTC, also supports clock calibration
10. JTAG/SWD interface: for debugging/programming
11. USB connector, used for establishing USB communication between PC and the STM32 development board
12. USART1 connector, supports ISP (In-System Programming) through USART1, as well as system signal output
13. IO expander, all the MCU pins are accessible on expansion connectors for further expansion
14. Power input/output header, 5V/3.3V, usually used for power output, or common ground with other user board
15. 5V DC power jack
16. Boot mode selection: for configuring the BOOT0 and BOOT1 pins
17. Power supply switch, powered from 5V DC jack or USB connection
18. OTG PWR OUT enable jumper
    • short the jumper to enable OTG PWR OUT
    • open the jumper to disable, as well as taking up no I/O port
19. OTG VBUS enable jumper
    • short the jumper to enable OTG VBUS
    • open the jumper to disable, as well as taking up no I/O port
20. VBAT selection jumper
    • short the jumper to use system power supply
    • open the jumper to connect the VBAT to external power, such as battery
21. VREF jumper
    • short the jumper to connect VREF+/VREF- respectively to VCC/GND
    • open the jumper to connect VREF+/VREF- to other custom pins via jumper wires
22. User LEDs jumper
    • short the jumper to connect to I/Os that used in example code
    • open the jumper to connect to other custom pins via jumper wires
23. User keys jumper
    • short the jumper to connect to I/Os that used in example code
    • open the jumper to connect to other custom pins via jumper wires
24. Joystick jumper
    • short the jumper to connect to I/Os that used in example code
    • open the jumper to connect to other custom pins via jumper wires

RE1KAT    RE8KAT  RE16KAT   RE2KAT

Do pobrania

	SCHEMAT MODUŁU

Package Contains

Port407Z development board x 1 USB type A to Mini-B cable x 1 USB power cable x 1 4-pin wire x 2 2-pin wire x 2 User guide CD x 1	1	2	3
	4	5	6