- Dead Cat Conversion Kit for SK450 Quadcopter Frame

- SK450 Dead Cat "Defibrillator" Power and A/V Distribution Board and Power Shield

Na sprzedaz zestaw zawierajacy:
- Dead Cat Conversion Kit for SK450 Quadcopter Frame (zestaw jest nowy, nieuzywany)

- SK450 Dead Cat "Defibrillator" Power and Audio/Video Distribution Board and Power Shield.
Plyta jest w zasadzie w niewielkim stopniu uzywana, byly do niej jedynie przlutowane ESC
i przewod laczacy z bateria. Projekt niestety nigdy sie nie wzniosl w powietrze z powodu
braku czasu i funduszy na dokonczenie (narodziny corki). Plyta dystrybucyjna w zadnym wypadku
nie jest porysowana, wyglada jak nowa i posiada jedynie niewielkie ilosci cyny ktore pozostaly
po wylutowaniu przewodow gdyz nie mam odsysarki.
Ps. Zestaw nie zawiera ramion(arms), czyli jest sprzedawany w takim stanie jak u producenta.
Do zlozenia wymaga ramiona(arms) od SK450 lub cala rame ktora posiadam na innej aukcji.
Opis producenta oraz pełna specyfikacja poniżej.

Opis producenta:

Dead Cat Conversion Kit for SK450 Quadcopter Frame

Are you looking to convert your SK450 quadcopter into a flying dead cat? If so, we have just
the thing! This kit allows you to convert your standard SK450 into the "Dead Cat" style configuration
with or without (your choice) the mess and hassle of mounting your own dead feline to the frame.

In addition to flying your deceased family pet around at home or your favorite local flying site,
this configuration is also ideal for aerial video/photography as the front arms offer an extra wide
field of view. The integrated camera mount plate located at the front of the frame is perfect
for mounting a GoPRO or similar sized camera.

This kit includes everything necessary to convert your SK450 quad frame into either a wicked camera
rig or a morbid dead pet mobile, the choice is yours!

*Note: This is a conversion kit only and requires the use of original SK450 frame parts to complete.

Specs:

1. Front arm width: 490mm
2. Rear arm width: 375mm
3. Weight: 460g (completed frame w/out electronics)

Includes:

1. Lower main frame plate
2. Upper main frame plate
3. All necessary hardware

SK450 Dead Cat "Defibrillator" Power and A/V Distribution Board and Power Shield

We pulled out the defibrillator and shocked some serious life in to the Dead Cat conversion!
The Spider style Quad-Copter was already awesome with its optimized arm angle and layout for
a propeller free FPV view. And now the much awaited progression to an integrated power
and A/V distribution board and plug in power shielded.

The new lower board has direct solder pads for the motor ESC power lines right at the base
of the arms and power “in” pads located directly above the battery to minimize cabling.
There are power connector’s at the front, back and middle for your FPV gear and flight controller,
all tied to the power shield which effortlessly supply’s a regulated, filtered and RF Noise shielded
5 volts at a whopping 3 amps for the camera and flight controller and 12 volts at 1 amp for
the hungriest of video transmitters. The video connectors at the front and rear also not only supply
the voltage but also carry the audio and video signal from the front mounted camera to the rear
mounted video transmitter. This upgrade will save you weight, clean up your layout and improve
reliability by reducing connection failures. I guess this Dead Cat has 9 lives after all!

Features:

1. • Integrated power distribution
2. • Wick style solder pads
3. • Camera and video transmitter integrated wiring
4. • 3 or 4 cell input
5. • SMPS converter with RF noise protection shield
6. • Thermal Protected

Specs:

1. Input voltage: 8-16v (3-4 cell lipoly)
2. weight: 142g
3. output: 5V/3A and 12V/1A

* Note the dead cat Defibrillator conversion for the SK450 requires the Sk450 frame and
Dead cat Conversion related below.